Single Stage Hammer Crusher

【Production capacity】：70-1000T/H Notice: this capacity is mean value, and the specific production capacity is subject to clients’ actual equipment configuration.

【Processable Material】：granite, marble, basalt, iron ore, cobble, shale, bluestone, coal, cobblestone, construction waste

【Range of Application】：Stone crushing in building materials industry ,highway and railway construction, housing and other industries.

Chat Online Leave Message

Product introduction

DPC series single-stage impact hammer crusher is one of the leading products in our company, which is widely used to crush limestone, stones with medium hardness, compressive strength under 200 Mpa and calcium content higher than 40%. It can crush the big size ore to the small size ones which can be directly fed to the grinding mill, thus replace the traditional two-stage crushing, simplify the process, save infrastructure investment and production cost.

Product superiority

Feed Port

Big feed port makes high charging rate.

Hydraulic Traction Bar

Rear cover could be opened by hydraulic traction bar, easy to change impact plate and easy to maintain.

Observation Door

When machine shut down, service condition could be observed.

Effecient and Energy-Saving

Single stage, and high capacity.

Working principle

DPC series single-stage impact hammer crusher is composed of rotor, bearing part, discharge dandruff comb, strike plate and shell. Hammer of the crusher strikes ore stone, ore stone hits impact plate and ore stone impacts each other, these are the principle of single stage hammer crusher. Ore stone is fed to feed port by feeder, then it will fall into crushing cavity where there are two relative rotating rotors, and impacted by hammer to get preliminary crushing. Material will be secondly crushed by rotor and impact plate in the process of falling down, then shunted by strike plate to go two mutual symmetry discharge area, finally, standard material will be discharged by bottom of the machine.

Technical Parameters

Model	Rotor Diameters (mm)	Hammerhead quantity (Pcs)	Feed size (mm)	Max.Feeding Size (mm)	Output Size (mm)	Capacity (t/h)	Power (KW)	Total Weight (t.excluding motor)	Model of Motor
DPC14.12	Φ1420×1194	26	1290×1320	600×600×900	≤25mm	70～120	200	23.5	YR355-6
DPC16.16	Φ1650×1630	28	1500×1785	800×800×1200	≤25mm	150～220	355	43	YRKK500-6
DPC18.18	Φ1850×1730	40	1755×1780	800×800×1000	≤25mm	240～350	560	67.5	YRKK500-6
DPC20.18	Φ2020×1802	40	2040×1860	1000×1000×1000	≤25mm	350～450	710	89	YRKK560-6
DPC20.22	Φ2018×2227	50	2288×2460	1000×1000×1200	≤25mm	400～600	800	110	YRKK560-6
DLPC20.22-1	Φ2018×2227	50	2288×2460	1000×1000×1500	≤25mm	600～800	800	120	YRKK560-6
DLPC20.22-2	Φ2018×2227	50	2288×2460	1000×1000×1500	≤25mm	700～900	800	130	YRKK560-6
2DPC18.18	Φ1850×1890	2×36	2030×2080	1000×1000×1200	≤75mm	700～1000	2×630	119	YRKK560-6
2DPC20.22	Φ2018×2238	2×50	2670×2460	1000×1000×1500	≤75mm	1200～1500	2×800	147	YRKK560-6
2DPC23.25	Φ2300×2508	2×66	3065×2666	1100×1100×1500	≤75mm	1200～1600	2×1120	204	YRKK6302-6